Wednesday, December 21, 2011

Toshiba NB255-N245, I get a blank screen

Try this followind method to get rid of Black Screen Problems.

1 . Take out your Laptop Battery
2. Remove your AC Adaptor Cord, that's the wall power, remove it.
3. Now hold down the Power Button for 30 Seconds
4. Then Plug your Battery and Plug it on the wall power
5. Then Power ON your laptop

if problems persist dont forget to leave some comment to solve your problems.
And I'll post some another tips





Monday, December 19, 2011

How to reset Canon Printer IP 1980 in manual process

Steps:
* Hold down press power Button of Printer, still press power button and plug power cable
* Still hold down press power button, press once the resume or reset button ( it will light a orange led), Then press it again resume or reset button but still hold down press the power button ( it will light a green Led)
*if you see Green Led it will be reset it already, then Release all button, if the printer blink to green it goes to resetting itself.

Friday, December 16, 2011

How to Check Internet Connection Loss


Check your Modem or Router if you have use this both, Try to Reset your Modem: Turn it Off power of your  Modem and Unplug Adapter, wait atleast 10 or 15 seconds, then Plug your Modem
and power on after that wait to see your Modem Leds are Green such as Link labels green Led. Then Open Browser and try browse.

if the problem still, contact your Tech Internet Broadband if need to replace your modem.

Why Messenger log-in takes too long


Here some tips if you having this problem:

* Check your Account you used: username and password if correct or mismatch (Be sure if you're username or password is correct)
* Check your Internet Connection or maybe the Server have problem or down
note: Reset your modem
* Try to Open in another Computer or Laptop if problem persist you should sign up a new account in Messenger (but you lost all your contacts)
* Uninstall Messenger and restart your Computer or Laptop, then Install Messenger again a latest or newer version.
* Update your Anti-virus or any program you used to protect your Windows, It's a kinda a spyware or virus infected sometimes.
* One tips be careful to open some untrusted site's..because it harm your Computer or Laptop.

Wednesday, December 14, 2011

How to fix Windows 7 will not boot: corrupted files [SOLVED!]

This is going to be quite a post, but here goes nothing:
I am running Windows 7 Pro 64-bit with SP1 installed, and until yesterday it was working fairly well. As many of you may know, yesterday was April Fool's Day, and
I'm afraid my computer played quite the joke on me! It was business as usual, and I was dragging a folder to the Recycle Bin when my desktop icons suddenly vanished. I decided to try a few basic troubleshooting tips to correct this: I disabled and re-enabled the "Show Desktop Icons" option, I changed my theme a couple of times, I set my desktop icons to default, and I rebooted the computer. However, nothing seemed to work. I knew the icons were still there, because I saw them in my Desktop folder, and my taskbar and Start menu were fine. The only way I could make the icons reappear was to use the trusty Winkey+ P, and switch the display option from "Computer Only" to "Parallel" or "Duplicate."

Running out of ideas, I quickly jumped online and searched our incredibly helpful forum. I found another which suggested rebuilding the icon cache. I entered in the following commands verbatim in an elevated command prompt:

taskkill /IM explorer.exe /F
CD /d %userprofile%\AppData\Local
DEL IconCache.db /a
shutdown /r


I know I should have changed the “userprofile” to my username, but I didn't realize that at the time. Anyway, the computer rebooted, but unfortunately, the desktop icon issue persisted. I decided to ignore it for the time being, and began syncing music to my iPod. A while later, there was a power outage, and my comp therefore shutdown unexpectedly. When I rebooted, Windows was all right. After checking to make sure nothing was out of place (besides the missing desktop icons) I shut down and left for several hours. Upon returning, I rebooted the computer and received my next April Fool's Joke – Windows would not boot! The machine would load up the GUI boot screen, but then, instead of displaying the login screen, I would see a black screen with just my cursor visible, and then the computer would reboot. It continued to do this in an unending cycle of failing to boot.

I used every single boot repair I knew, starting with the F8 options: I tried Safe Mode and Last Known Good Configuration, both with the same results as if I'd booted normally. I ran the kernel debugger with no result, and I ran a memory test, but that came back clean. Naturally, Windows suggested that I attempt to repair it at the boot menu, so I decided to run Startup Repair. It found and attempted to repair an error, but was unable to do so. Thinking that the pre-installed files could be bad, I ran Startup Repair again from my genuine Windows 7 install disc, but the result was the same. The following error report was displayed when I requested further details:

Problem event name: Startup Repair Offline

Problem locations (I omitted some because they were either blank or unknown):
1.) 6.1.7600.16385
4.) 21202109
5.) External Media (This led me to believe there was some sort of conflict with the iPod, but I made sure nothing was plugged in when I rebooted other than my monitor, keyboard, and mouse.)
6.) 2
7.) No Root Cause

That last bit is somewhat contradictory, because further along in the error report, one root cause was found, and was listed as “Unspecified changes to system configuration might have caused the problem.” Perhaps the error was caused my attempt at rebuilding the icon cache? That is my best guess, because my computer passed every other check the Startup Repair ran.
Since Windows couldn't repair the system, my next step was to use System Restore. However, there were no restore points available! For some reason, Windows wouldn't let me access them, although I knew I had them, since Windows had created a restore point when I installed SP1. Since restore points were now no longer an option, my next plan was to restore from a system image I had made a few weeks earlier. I decided to refrain from that option, because I am hoping I may find a solution here that will fix my boot issue, rather than setting me back a few weeks. If all else fails, I can use my system image.
Since the repair options from the Windows install disc hadn't worked or uncovered anything, and neither had the F8 advanced boot options, I moved to plan B. I have a separate hard drive with Windows XP and Linux Mint installed on it, so I decided to check my Windows 7 drive from there. I booted into XP and ran several virus, rootkit, and malware scans, including an exhaustive scan with McAfee's free anti-virus tool. Every scan came back negative, so apparently there wasn't any malware infection that might have compromised my main drive. I checked the drive for errors with XP's built-in utility, and that also came back clean. So the disc was healthy, which confirmed the Startup Repair's report that there were no bad sectors.

I was fresh out of ideas, so I decided to sleep on it and shut the computer down. When I rebooted this morning, I was unable to access my XP drive! When I selected XP from the boot loader menu, instead of booting XP up as usual, the screen moved to the Windows 7 boot GUI and then entered its boot failure cycle. So now, for some reason, the Windows 7 boot error has moved to my second hard drive and taken out my XP boot loader. I can still boot with Linux, so I can still access my XP and Win 7 partitions, in case I need to change anything in the boot folder or edit any configuration files.

Thus concludes my post; I'm sorry if it appears verbose, but I really wanted to cover the entire problem in great detail, just so that a solution may be found that much quicker. So is there a method I haven't thought of yet that may yet save me from restoring or reinstalling Windows? I'm not sure what incited the issue in the first place, but I believe it was either my botched attempt at rebuilding the icon cache, the boot files becoming corrupted as a result of being unexpectedly shut down during the power outage, or even a delayed side-effect from installing Service Pack 1. I haven't installed or downloaded anything recently (aside from updating Firefox) so I really don't know the cause for this boot disorder. And why would Windows 7's inability to boot suddenly afflict XP, which is on a separate hard drive? As I said, I'm completely out of ideas, and this April Fool's joke has me entirely confounded!

Tuesday, December 13, 2011

Steps for PC Troubleshooting

(1) Trial-and-error

Personal computers are highly modular by design. The most powerful trouble-shooting technique is to isolate the problem to a specific component by trial-and-error. Swap compatible components and see if the system still works. Try different peripherals on different machines and see if the same problem occurs. Make one change at a time.

(2) "It's the cable"

 More than 70% of all computer problems are related to cabling and connections. Ensure all cables are connected firmly. IDE and floppy ribbon cables and power cables can often go loose. Ensure microprocessor, memory modules, and adapters such as video card and sound card are inserted correctly and didn't "pop-up" during transportation.

(3) Don't be frustrated!

Don't be afraid of computer problems. It is often the best opportunity to learn. Trouble-shooting is part of the fun of owning a computer. Imagine the satisfaction you could get by solving a problem yourself.

Of course the fun could ran out quickly once you are frustrated and have spent too much time on the same problem. If you feel frustrated, it's time to leave it for a while and go back with some new ideas or call someone who can help. Rule of thumb: You shouldn't spend more than three hours on the same problem at one time.

(4) Take notes!

Take notes of what you have done and all the error messages. You may need to use them later. For instance, when you see an unusual blue screen with an error message, copy the entire message onto a piece of paper. In many situations, that message may point to the right direction in getting the problem solved quickly.

(5) Take a look?

It's OK to open a computer case and take a look inside. There is only 5V and 12V DC voltage supplied to the components outside the power supply. Those who have never seen the inside of a computer are often amazed by how simple it looks. Of course, still always power down and unplug the power cord first.

Basic Steps to Troubleshoot Desktop Computer

  • Restart the computer.
  • Check your cables. Keyboard not working? Make sure it's plugged in. Mouse not responding? Make sure it's plugged in.
  • Check the electric power. Plug a lamp into the same power outlet that's connected to your computer to make sure the outlet is working.
  • Make sure the computer and monitor are plugged in.
  • Disconnect all peripheral devices (such as a printer or external Zip disk) and restart the computer.
  • Listen for unusual sounds. Is the cooling fan running? Is the hard drive making noises?
  • Look inside the computer for wires that aren't plugged in all the way or other faulty connections.
  • Start the computer from an external start-up disk, such as your bootdisk or cd recovery 

How to repiar System windows file problem

Some even worse version of the problem can occur if an application overwrites some of the shared system files used by Windows 95—although that often means the operating system won’t load. (The same types of problems can also happen with Windows 98 or Windows ME, although Win98's System File Checker utility can help take care of these problems much more easily.) If that’s the case—it is relatively rare—you’ll probably need to reinstall Windows itself. (And if you do, you'll probably need to have a boot disk complete with a CD-ROM driver.

If you think it's time to reinstall Windows, you might try the Windows Setup program's Verify option first—it should save you time and maybe even a few extra headaches. The Verify option is supposed to be available any time you run Windows 95, 98 or Windows ME Setup on a machine that already has the same version of the operating system installed (although I've found that it doesn't always show up for some reason).

What happens is, the Setup program detects that Windows is already installed and then asks if you'd like to Verify your installation. If you do choose to Verify, it goes through an installation log file called Setuplog.txt (you can find it in your main hard drive's root directory--e.g., C:\--if you want to look at it) to see what should be installed, confirms that all the required files exist and aren't damaged, and then silently reinstalls any components that it finds are missing or damaged. In some cases, this will solve Windows system problems.

Sunday, December 11, 2011

How to repair Windows Vista registry

I will recommend you Registry Repair. It is a fully dedicated tool for windows vista. It scans the registry and look for any incorrect values in it. This value's are created by virus or malicious applications. It has an backup and restore feature also. You can take a fresh back of your registry file and restore it back in case of any error. It regularly scans the current status of registry to avoid system failure at an extent. It works in both 64 bit and 32 bit version. Some of its best function I like are :
  • It automatically scans and clean up registry.
  • It has a tracks eraser feature.
  • It initiates in improving system performance.
  • It removes trojan.

leave comment to download tools :)

Task Bar problem with windows 7

We like the new Windows 7 taskbar, but many people seem less than impressed with the new approach to taskbar buttons, finding it difficult to tell at a glance whether an icon is a running application or a pinned shortcut. If this sounds like you then there's an easy way to restore more standard taskbar buttons, though - right-click the taskbar, select Properties, and set Taskbar Buttons to "Never combine" or "Combine when taskbar is full".
You can even restore the old Quick Launch toolbar in just a few clicks. Simply right-click the taskbar, click Toolbars > New Toolbar, type %userprofile%\AppData\Roaming\Microsoft\Internet Explorer\Quick Launch in the folder box and click Select Folder. The Quick Launch toolbar should then reappear, and you can move and resize it to suit your needs.

Windows 7 taskbar

 Just a few seconds work and your taskbar has that retro look

Windows 7 poor video quality

Steps to configured video quality

The new Windows 7 power plan settings affect more of your software than ever before. If you notice video playback quality seems poor, for instance, then click Start, type Power Options and click the Power Options link. Click Change Plan Settings for your currently selected plan, click Change Advanced Settings, expand the Multimedia Settings section and make sure "Playing video" is set to "Optimise performance".
Alternatively, if you often play video on a laptop, then change the new setting to "Optimise performance" and you may see an improvement in battery life.

Missing applets of Windows 7

Windows 7 installs quickly and takes up less hard drive space than you might expect, but in part that's down to cheating - Mail, Movie Maker, Photo Gallery and other applets are no longer bundled with a standard Windows installation.
Installing Live Essentials will also get you potentially unnecessary extras, though, like an ActiveX control to help in uploading files to Windows Live SkyDrive. And the Windows Live Sign-In Assistant, which can be useful if you want to switch between multiple Windows Live accounts. If you have only one Windows Live account, and no plans to use Live SkyDrive, then these can safely be removed from the Control Panel Uninstall A Program applet.

Windows live essentials


You can install as many, or as few of the Live Essentials programs as you like

iPhone cant sync in Windows 7

Irritated iPhone users are major difficulties in getting their iPhone to sync with Windows 7 systems. Particularly 64-bit Windows 7 systems, based around the P55 chipset. The iPhone is usually (though not always) recognised, but iTunes then complains that it can't connect to the unit because of an "unknown error", usually (though again, not always) 0xE8000065.
Disabling USB power management appears to be one solution. Click Start, type DEVMGMT.MSC and press [Enter] to launch Device Manager, then click View > Devices By Type. Expand the Universal Serial Bus controllers section of the tree, right-click each USB Root Hub entry in turn, select Properties > Power Management, and clear "Allow the computer to turn off this device to save power".
Reboot your PC after this tweak and try again. This works for some, but if you're out of luck then check the Apple Discussions thread for other ideas.

iTunes on windows 7\

iTunes on Windows 7 won't always see, or sync with, your iPod

Vista upgrade hangs up

 Windows 7 can start causing problems before it's even installed, as many people report their upgrade hangs forever at 62%. Which is annoying.
Reboot, and your PC should roll back to Windows Vista. You can then open the setup log file \$WINDOWS.~BT\Sources\Panther\setupact.log to view what happened. Microsoft say this is usually caused because the Iphlpsvc service has stopped responding, and just adding an environment variable to ignore it will fix the problem.

If this doesn't help (or your upgrade hangs at something other than 62%) then browse the setup log for other clues. And you might also try to boot and install from the Windows 7 disc, if possible, as that reduces the chance of any conflict with your existing Vista (or XP) setup.

Windows 7 cant boot

Try Repairing The Windows 7 Installation

1. Insert the Windows 7 DVD and restart your computer
2. Boot from the DVD.
3. Choose your language and click Next.
4. Click Repair Your Computer and then select the operating system you want to repair.


If that doesn't fix it:

1. Insert the Windows 7 DVD and restart your computer
2. Boot from the DVD.
3. Choose your language and click Next.
4. Click Repair Your Computer and then select Command Prompt and try the following commands (a single command might work, or you may need to use multiple commands depending on the exact problem):

bootrec /fixMBR
bootrec /fixBoot
bootrec /rebuildBCD


Note: there is a space before the /

How to Reset Canon IP 1980

To perform Full Tank Ink Resetter on IP in 1980 is usually the indicator light on the power and resume blinking repeatedly do when that happens the next steps:
 
First. Turn on the printer Canon iP1900
2. Press and hold the resume button for 2 minutes.
3. Release the Resume button.
4. The printer will return to normal.
5. If still not normal too, do the steps as for manual reset and Reset software
 
Steps for Manual Reset
 
First. Printer power cable plugs in a state separated
2. Press and hold down the power button with your index finger and then the input power cable
3. Still hold the power button, then press the middle finger Button reset button twice.
4. Release the power button
5. The printer is not blinking
6. At this stage you've completed the steps Manual Reset
7. In order to permanently software please use the Reset.
 
 
Do his steps as follows:
 
First. Make sure all files are free of attribute Read Only.
2. Run GeneralTool.exe GeneralTool iP1900
3. USB Port select the port on your printer.
4. Click the Lock Release
5. Select (check) the EEPROM CLEAR
6. Provide blank paper for printing. Then Click the Test Pattern 1
7. Finish your IP1900 Printer back to normal.

Windows Vista Ultimate Key

 
Serial Key
 
TCV33-CH82D-VC8KY-4YW8F-3VKH
MCVQ7-P79TY-PFCJ4-HXH74-YRD9J        
TCp8w-t8pqj-wwrrh-qh76c-99fbw       
YFKBB-PQJJV-G996G-VWGXY-2V3X8       
BG9P2-VFK9D-RHR8G-2448C-9B4J2       
YFKBB-PQJJV-G996G-VWGXY-2V3X8       
GLAD2-SEEUH-AVEAS-ENSEO-FHUMR       
GKFV7-F2D9H-QKYXY-777P3-4M73W       
7RP8P-6BHPW-J82BD-QQX72-W8M93         
2PHXF-9PBDW-D3WWY-CPDKD-XG87V       
HQDKC-F3P6D-C9YYM-HRB89-QDBB7        
TCP8W-T8PQJ-WWRRH-QH76C-99FBW       
V7KPK-CRWQ9-8F374-2KGPC-QCKG8       
R4HB8-QGQK4-79X38-QH3HK-Q3PJ6       
TGX39-HB48W-R29DH-6BVKB-3XFDW       
cky24-q8qrh-x3kmr-c6bcy-t847y

Windows Xp Serial Key

Enjoy! :)
 
7QVT6-T2738-WRKJB-YKRFQ-XVK98

Bios Beep Codes

AMI BIOS beep codes
 
Below are the AMI BIOS Beep codes that can occur. However, because of the wide variety of different computer manufacturers with this BIOS, the beep codes may vary.
Beep Code Descriptions
1 short DRAM refresh failure
2 short Parity circuit failure
3 short Base 64K RAM failure
4 short System timer failure
5 short Process failure
6 short Keyboard controller Gate A20 error
7 short Virtual mode exception error
8 short Display memory Read/Write test failure
9 short ROM BIOS checksum failure
10 short CMOS shutdown Read/Write error
11 short Cache Memory error
1 long, 3 short Conventional/Extended memory failure
1 long, 8 short Display/Retrace test failed
 
AWARD BIOS beep codes
 
Below are Award BIOS Beep codes that can occur. However, because of the wide variety of different computer manufacturers with this BIOS, the beep codes may vary.
Beep Code Description
1 long, 2 short Indicates a video error has occurred and the BIOS cannot initialize the video screen to display any additional information
Any other beep(s) RAM problem.
 
If any other correctable hardware issues, the BIOS will display a message.
 
IBM BIOS beep codes
 
Below are general IBM BIOS Beep codes that can occur. However, because of the wide variety of models shipping with this BIOS, the beep codes may vary.
Beep Code Description
No Beeps No Power, Loose Card, or Short.
1 Short Beep Normal POST, computer is ok.
2 Short Beep POST error, review screen for error code.
Continuous Beep No Power, Loose Card, or Short.
Repeating Short Beep No Power, Loose Card, or Short.
One Long and one Short Beep Motherboard issue.
One Long and Two Short Beeps Video (Mono/CGA Display Circuitry) issue.
One Long and Three Short Beeps. Video (EGA) Display Circuitry.
Three Long Beeps Keyboard / Keyboard card error.
One Beep, Blank or Incorrect Display Video Display Circuitry.
 
Macintosh startup tones
Tones Error
Error Tone. (two sets of different tones) Problem with logic board or SCSI bus.
Startup tone, drive spins, no video Problem with video controller.
Powers on, no tone. Logic board problem.
High Tone, four higher tones. Problem with SIMM.
 
Phoenix BIOS beep codes
 
Below are the beep codes for Phoenix BIOS Q3.07 OR 4.X
Beep Code Description / What to Check
1-1-1-3 Verify Real Mode.
1-1-2-1 Get CPU type.
1-1-2-3 Initialize system hardware.
1-1-3-1 Initialize chipset registers with initial POST values.
1-1-3-2 Set in POST flag.
1-1-3-3 Initialize CPU registers.
1-1-4-1 Initialize cache to initial POST values.
1-1-4-3 Initialize I/O.
1-2-1-1 Initialize Power Management.
1-2-1-2 Load alternate registers with initial POST values.
1-2-1-3 Jump to UserPatch0.
1-2-2-1 Initialize keyboard controller.
1-2-2-3 BIOS ROM checksum.
1-2-3-1 8254 timer initialization.
1-2-3-3 8237 DMA controller initialization.
1-2-4-1 Reset Programmable Interrupt Controller.
1-3-1-1 Test DRAM refresh.
1-3-1-3 Test 8742 Keyboard Controller.
1-3-2-1 Set ES segment to register to 4 GB.
1-3-3-1 28 Autosize DRAM.
1-3-3-3 Clear 512K base RAM.
1-3-4-1 Test 512 base address lines.
1-3-4-3 Test 512K base memory.
1-4-1-3 Test CPU bus-clock frequency.
1-4-2-4 Reinitialize the chipset.
1-4-3-1 Shadow system BIOS ROM.
1-4-3-2 Reinitialize the cache.
1-4-3-3 Autosize cache.
1-4-4-1 Configure advanced chipset registers.
1-4-4-2 Load alternate registers with CMOS values.
2-1-1-1 Set Initial CPU speed.
2-1-1-3 Initialize interrupt vectors.
2-1-2-1 Initialize BIOS interrupts.
2-1-2-3 Check ROM copyright notice.
2-1-2-4 Initialize manager for PCI Options ROMs.
2-1-3-1 Check video configuration against CMOS.
2-1-3-2 Initialize PCI bus and devices.
2-1-3-3 Initialize all video adapters in system.
2-1-4-1 Shadow video BIOS ROM.
2-1-4-3 Display copyright notice.
2-2-1-1 Display CPU type and speed.
2-2-1-3 Test keyboard.
2-2-2-1 Set key click if enabled.
2-2-2-3 56 Enable keyboard.
2-2-3-1 Test for unexpected interrupts.
2-2-3-3 Display prompt Press F2 to enter SETUP.
2-2-4-1 Test RAM between 512 and 640k.
2-3-1-1 Test expanded memory.
2-3-1-3 Test extended memory address lines.
2-3-2-1 Jump to UserPatch1.
2-3-2-3 Configure advanced cache registers.
2-3-3-1 Enable external and CPU caches.
2-3-3-3 Display external cache size.
2-3-4-1 Display shadow message.
2-3-4-3 Display non-disposable segments.
2-4-1-1 Display error messages.
2-4-1-3 Check for configuration errors.
2-4-2-1 Test real-time clock.
2-4-2-3 Check for keyboard errors
2-4-4-1 Set up hardware interrupts vectors.
2-4-4-3 Test coprocessor if present.
3-1-1-1 Disable onboard I/O ports.
3-1-1-3 Detect and install external RS232 ports.
3-1-2-1 Detect and install external parallel ports.
3-1-2-3 Re-initialize onboard I/O ports.
3-1-3-1 Initialize BIOS Data Area.
3-1-3-3 Initialize Extended BIOS Data Area.
3-1-4-1 Initialize floppy controller.
3-2-1-1 Initialize hard-disk controller.
3-2-1-2 Initialize local-bus hard-disk controller.
3-2-1-3 Jump to UserPatch2.
3-2-2-1 Disable A20 address line.
3-2-2-3 Clear huge ES segment register.
3-2-3-1 Search for option ROMs.
3-2-3-3 Shadow option ROMs.
3-2-4-1 Set up Power Management.
3-2-4-3 Enable hardware interrupts.
3-3-1-1 Set time of day.
3-3-1-3 Check key lock.
3-3-3-1 Erase F2 prompt.
3-3-3-3 Scan for F2 key stroke.
3-3-4-1 Enter SETUP.
3-3-4-3 Clear in-POST flag.
3-4-1-1 Check for errors
3-4-1-3 POST done--prepare to boot operating system.
3-4-2-1 One beep.
3-4-2-3 Check password (optional).
3-4-3-1 Clear global descriptor table.
3-4-4-1 Clear parity checkers.
3-4-4-3 Clear screen (optional).
3-4-4-4 Check virus and backup reminders.
4-1-1-1 Try to boot with INT 19.
4-2-1-1 Interrupt handler error.
4-2-1-3 Unknown interrupt error.
4-2-2-1 Pending interrupt error.
4-2-2-3 Initialize option ROM error.
4-2-3-1 Shutdown error.
4-2-3-3 Extended Block Move.
4-2-4-1 Shutdown 10 error.
4-3-1-3 Initialize the chipset.
4-3-1-4 Initialize refresh counter.
4-3-2-1 Check for Forced Flash.
4-3-2-2 Check HW status of ROM.
4-3-2-3 BIOS ROM is OK.
4-3-2-4 Do a complete RAM test.
4-3-3-1 Do OEM initialization.
4-3-3-2 Initialize interrupt controller.
4-3-3-3 Read in bootstrap code.
4-3-3-4 Initialize all vectors.
4-3-4-1 Boot the Flash program.
4-3-4-2 Initialize the boot device.
4-3-4-3 Boot code was read OK.

Internet Connection Problem

Steps to check your Internet Connection:
Check your Modem connected through your Computer
Check your UTP Cable or try to change your UTP Cable
Then Check your Driver Your Network Card is Available or Detect in your Device Manager

Helpful Tips About Computer


1)These are the step to continously Intact your computer
 
2)It would be helpful to protect your computer by using an UPS (uninterruptible power supply) , so as your computer will not be damaged by an unexpected brownout.
 
3)It is strongly recommended to backup your archives which are important for you and you would like to protect them. There are many types of storage devices such as external hard drives, USB sticks, CD’s etc.
4)Occasionally, you may run the scandisk and the defragment function, in order to avoid potentially serious damages to your hard drive. You can either buy a service pack, provided by stores which have your computer’s brand name.
 
5)You should not remove peripheral devices from your computer while it is activated, because this could have a negative influence on either to the connector socket or the motherboard. This action is strictly allowed only if you are equipped with a peripheral device guaranteed to be "hot pluggable".
6)Make sure to maintain at least 300 MB of free space at your hard drive so as to be used by the Windows Operating System. For Windows XP, Vista, or Windows 7 the preferable amount of free space should be about 500 MB on your C: Drive. The absence of empty space in your hard drive will definitely end up causing serious malfunction to your computer, including data loss and deformation. It is also very usual to confront extremely low speed when you are trying to execute a task. Be sure to make the most of the ADD/Delete tool in the Windows Control Panel to get rid of useless programs which are installed at your hard drive. There are also several programs designed especially for "cleaning" and speeding up your computer.
7)When you switch on your computer, you should not permit ample programs loading up as long as they consume inestimable amount of your computer’s memory and Windows Resources. In case you don’t use all programs in your Windows System Tray, it is recommended to lock them and let them load up after computer’s booting.
8)It is important to install an antivirus program to your computer, which is loading up the time you turn on your computer. You will be perfectly protected in case you choose a continuous observing antivirus program, that is automatically updated.
9)Since you have a high speed Internet connection, it is certain that you must have installed a firewall program. A firewall program is used to maintain your computer safe from malicious attacks against your system. It would be best to avoid allowing someone other than you having access to your data and files. Nowadays all new computers are equipped with a built-in firewall program. You can easily change the firewall’s settings by accessing the control panel but you should remember to keep the firewall activated. In case you need some additional protection for your computer it would be best to take into consideration some security software available in stores such as Panda AntiVirus Pro, BitDefender Total Security and Kaspersky Internet Security. All these programs are enriched with firewall, antivirus and plenty other security features.
10)You should also check computer and peripheral devices’ software discs and keep them in a safe enviroment, as they enclose useful programs and files for your Windows Version.
Compaq Presario 4090US Desktop PC no access internet1)When you switch off your computer, you should firstly wait to complete the Windows shutdown procedure and then press the power button. Only if your hard disc is not running or your computer is not functioning properly, you can turn it off with the power switch, avoiding damages to the hard disc.

Smart Bro Canopy Fix

Ok guys im posting it her I have only copy this is another method to go or configure your canopy settings for those who cant access through
IP address: 169.254.3.3
Subnet mask: 255.255.0.0
or etc.. etc.. etc..
if you cant access through this
 
 
 
WELL TRY THIS ONE!
 
WARNING: During the process, you will be disconnected from the internet, but of course you'll be able to get back. So I suggest you copy and paste this tutorial on notepad for a safer reference, just in case.
 
Follow the steps:
1. Go to Control Panel, and then onto Network Connections.
You should see your Local Area Connection. Right click on it and click Properties.
 
2. A new window pops-up, which says "Local Area Connection Properties".
On the General tab, there should be a box which contains a list with checkboxes beside them.
Scroll down to the bottom and you should see the Internet Protocol (TCP/IP) item. Double click it.
 
3. Another window pops-out. It says "Internet Protocol (TCP/IP) Properties" and you should be on the General tab.
There are two options there enabled by default: Obtain an IP address automatically and Obtain DNS server
address automatically. Now read carefully for this one:
- Click on Use the following IP address option. Enter these data:
- IP address: 10.20.30.40
- Subnet mask: 255.0.0.0
- Default gateway: leave it blank
- Click on Use the following DNS Server addresses:
- Preferred DNS server: leave it blank
- Alternate DNS server: leave it blank
After you entered correctly all the data, press Ok.
 
4. You are back at the Local Area Connection Properties window.
Press Ok to apply the changes. Wait for a moment for the changes to take effect.
By this time you will be disconnected from the internet.
But dont worry, you'll be able to be back of course
(Just refer to PART 4 below to know how to get back to the internet).
 
 PART 2: The Canopy IP Address Quest
 
Now you need to know your Canopy IP Address. There are two ways I know of:
 
-> Method 1 (The Safe Way):
1. Go to Start -> Run -> cmd.exe. On the command promt,
type arp -a (take note of the space after the word arp).
The command prompt will display several IP addresses. Example:
 
C:\Documents and Settings\giluk_no_jutsu>arp -a
Interface: 10.20.30.40 --- 0x2
Internet Address Physical Address Type
10.0.0.1 0a-00-3e-f7-de-2d dynamic
10.247.222.45 0a-00-3e-f7-de-2d dynamic
 
So my Canopy IP Address would be 10.247.222.45.
 
 PART 3: Into the Forbidden Domain we Hack!
 
Note: Make sure you have done the set-up on Part 1 above before proceeding.
 
1. Open your web browser and enter your Canopy IP address on the address bar. You will be brought to the Canopy Homepage.
 
2. On the left side of the Canopy page, you should see a navigation box. Click Configuration.
 
3. Click on the Quality of Service (QoS) Tab.
You should see your Bandwidth Settings.
Take a look at your Sustained Uplink Data Rate and Sustained Downlink Data Rate.
By default they should be both at 256. See? Those are your default download and upload limits. Kinda sucks right?
 
4. Alright, so listen well. Change both of the Uplink and Downlink values to 500.
Actually you can set the values to any number you like as long as their total would be 1000
(eg: you can have your downlink: 600 and uplink: 400, or you can have downlink: 700 and uplink: 300).
However, The recommended value for both uplink and downlink rates is both at 500.
So I suggest you have the recommended value as well. Click the Save Changes button.
 
5. The screen should say Reboot Required. So press the Reboot button. By this time,
your Local Area Connection icon on your tray area (botton-right side of your desktop)
should have an X mark on it. Just wait for a while until that X mark disappears. That's it.
 
 PART 4: Getting Back Online
 
The last thing you need to do is to connect back to the internet.
 
1. So go back to Control Panel, and then onto Network Connections.
You should see your Local Area Connection. Right click on it and click Properties.
 
2. A new window pops-up, which says "Local Area Connection Properties".
On the General tab, there should be a box which contains a list with checkboxes beside them.
Scroll down to the bottom and you should see the Internet Protocol (TCP/IP) item. Double click it.
 
3. Another window pops-out. It says "Internet Protocol (TCP/IP) Properties"
and you should be on the General tab. Now click on Obtain IP address automatically and Obtain DNS server automatically.
Press Ok.
 
4. You're back at the Local Area Connection Properties window. Again Press Ok.
Wait for a moment for the changes to take effect.
 
5. Open your web browser and try to test your speed at speedtest.com or testmy.net to
confirm your new download and upload speeds. You can also try going to YouTube and watch the buffer speed go zoom zoom zoom!
 
Cheers GUYS!
Whew! That's it. Enjoy Surfin! 
I hope it works!!!

JBLCF ID Knight Conficker

 
recently encountered a virus on my laptop. I suspect it came from USB drives that came from Internet Cafes.
Symptoms:

Changes Folder Options to "Do not show hidden files or folders" and "Hide extensions for known file types" on  startup.
When trying to run the Command Prompt, your computer immediately shuts down.
Im using AVG but it cannot detect the virus. I uninstalled it and try out Norton 2009, still to no avail. Even McAffe online scan does not detect it. I think most anti virus softwares do not have the updates yet. So I just did my own research.
This seems to get rid of the above symptoms. Though Im not sure about the extent of the infection. Anyway heres what I did:
First turn off system restore.
Open Task Manager by pressing Ctr + Alt + Delete. Find and kill  "JBLCF_Scandal.exe" .
Next, we need to delete the files associated with it. Its invisible even if you set Show Hidden Files on Folder Options. 
So we open the registry editor. Start Menu > Run > regedit
Make sure to backup the registry first before doing anything!
Go to [HKEY_CURRENT_USER\Software\Microsoft\Windows\
CurrentVersion\Explorer\Advanced]
"ShowSuperHidden"=1
Everytime a command prompt is opened, system shuts down. So we go to [HKEY_CURRENT_USER\Software\Microsoft\Command Processor]
"autorun"="c:\Windows\pc-off.bat" –> remove "c:\Windows\pc-off.bat" or delete the autorun key.
Now go to the Windows directory and delete "c:\Windows\jblcf_scandal.exe". This file is visible by now since we set "ShowSuperHidden"=1.
Also delete "c:\Windows\pc-off.bat".
Thats it. Now for your own sake, go back to the registry editor and set "ShowSuperHidden"=0. This will make critical system files invisible again, and therefore safe from those naughty fingers of yours.
Goodluck
 
Leave a comment of your Email so that i can email you the tools.
 
recently encountered a virus on my laptop. I suspect it came from USB drives that came from Internet Cafes.
Symptoms:
Changes Folder Options to "Do not show hidden files or folders" and "Hide extensions for known file types" on  startup.
When trying to run the Command Prompt, your computer immediately shuts down.
Im using AVG but it cannot detect the virus. I uninstalled it and try out Norton 2009, still to no avail. Even McAffe online scan does not detect it. I think most anti virus softwares do not have the updates yet. So I just did my own research.
This seems to get rid of the above symptoms. Though Im not sure about the extent of the infection. Anyway heres what I did:
First turn off system restore.
Open Task Manager by pressing Ctr + Alt + Delete. Find and kill  "JBLCF_Scandal.exe" .
Next, we need to delete the files associated with it. Its invisible even if you set Show Hidden Files on Folder Options. 
So we open the registry editor. Start Menu > Run > regedit
Make sure to backup the registry first before doing anything!
Go to [HKEY_CURRENT_USER\Software\Microsoft\Windows\
CurrentVersion\Explorer\Advanced]
"ShowSuperHidden"=1
Everytime a command prompt is opened, system shuts down. So we go to [HKEY_CURRENT_USER\Software\Microsoft\Command Processor]
"autorun"="c:\Windows\pc-off.bat" –> remove "c:\Windows\pc-off.bat" or delete the autorun key.
Now go to the Windows directory and delete "c:\Windows\jblcf_scandal.exe". This file is visible by now since we set "ShowSuperHidden"=1.
Also delete "c:\Windows\pc-off.bat".
Thats it. Now for your own sake, go back to the registry editor and set "ShowSuperHidden"=0. This will make critical system files invisible again, and therefore safe from those naughty fingers of yours.
Goodluck
 
Leave a comment of your Email so that i can email you the tools.

Monday, December 5, 2011

Helpful Tips About Computer


1)When you switch off your computer, you should firstly wait to complete the Windows shutdown procedure and then press the power button. Only if your hard disc is not running or your computer is not functioning properly, you can turn it off with the power switch, avoiding damages to the hard disc.

2)It would be helpful to protect your computer by using an UPS (uninterruptible power supply) , so as your computer will not be damaged by an unexpected brownout.

3)It is strongly recommended to backup your archives which are important for you and you would like to protect them. There are many types of storage devices such as external hard drives, USB sticks, CD’s etc.
4)Occasionally, you may run the scandisk and the defragment function, in order to avoid potentially serious damages to your hard drive. You can either buy a service pack, provided by stores which have your computer’s brand name.

5)You should not remove peripheral devices from your computer while it is activated, because this could have a negative influence on either to the connector socket or the motherboard. This action is strictly allowed only if you are equipped with a peripheral device guaranteed to be “hot pluggable”.
6)Make sure to maintain at least 300 MB of free space at your hard drive so as to be used by the Windows Operating System. For Windows XP, Vista, or Windows 7 the preferable amount of free space should be about 500 MB on your C: Drive. The absence of empty space in your hard drive will definitely end up causing serious malfunction to your computer, including data loss and deformation. It is also very usual to confront extremely low speed when you are trying to execute a task. Be sure to make the most of the ADD/Delete tool in the Windows Control Panel to get rid of useless programs which are installed at your hard drive. There are also several programs designed especially for “cleaning” and speeding up your computer.
7)When you switch on your computer, you should not permit ample programs loading up as long as they consume inestimable amount of your computer’s memory and Windows Resources. In case you don’t use all programs in your Windows System Tray, it is recommended to lock them and let them load up after computer’s booting.
8)It is important to install an antivirus program to your computer, which is loading up the time you turn on your computer. You will be perfectly protected in case you choose a continuous observing antivirus program, that is automatically updated.
9)Since you have a high speed Internet connection, it is certain that you must have installed a firewall program. A firewall program is used to maintain your computer safe from malicious attacks against your system. It would be best to avoid allowing someone other than you having access to your data and files. Nowadays all new computers are equipped with a built-in firewall program. You can easily change the firewall’s settings by accessing the control panel but you should remember to keep the firewall activated. In case you need some additional protection for your computer it would be best to take into consideration some security software available in stores such as Panda AntiVirus Pro, BitDefender Total Security and Kaspersky Internet Security. All these programs are enriched with firewall, antivirus and plenty other security features.
10)You should also check computer and peripheral devices’ software discs and keep them in a safe enviroment, as they enclose useful programs and files for your Windows Version.

Thursday, December 1, 2011

Toshiba wavy lines in picture

It could be the problems is your drivers of video card (built-in) try to uninstall the previous driver then download a new driver. just go in google search engine and type toshiba video card drivers and look some options.

Compaq Presario 4090US Desktop PC no access internet

Steps to check your Internet Connection:
Check your Modem connected through your Computer
Check your UTP Cable or try to change your UTP Cable
Then Check your Driver Your Network Card is Available or Detect in your Device Manager

Just leave a comment if problem persist :)